Editing Barcode for SME Installation Instructions

Jump to navigation Jump to search

Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.

Latest revision Your text
Line 2: Line 2:
  
 
<span style="color:orange">'''First'''</span>
 
<span style="color:orange">'''First'''</span>
−
# On the MT-2090 Scroll and select '''Config...'''
+
<br>1. On the MT-2900 Scroll and select '''Config...'''
−
# Scroll to and select '''Configure USB'''
+
<br>2. Scroll to and select '''Configure USB'''
−
# Scroll to '''ActiveSync''' and press''' ENT''' then '''Close'''
+
<br>3. Scroll to '''ActiveSync''' and press''' ENT''' then '''Close'''
 
<br><span style="color:orange">'''Second'''</span>
 
<br><span style="color:orange">'''Second'''</span>
−
# Scroll to and select '''Wireless Companion''' (Also inside Config)
+
<br>1. Scroll to and select '''Wireless Companion''' (Also inside Config)
−
# If the second to bottom item says 'Disable Radio', Scroll to it and press '''ENT'''
+
<br>2. If the second to bottom item says 'Disable Radio', Scroll to it and press '''ENT'''
−
# If Not, scroll to Exit Press ENT then Answer yes to the Pop-Up window.
+
<br>3. If Not, scroll to Exit Press ENT then Answer yes to the Pop-Up window.
 
<br><span style="color:orange">'''Third'''</span>
 
<br><span style="color:orange">'''Third'''</span>
−
# Plug the Device into your Computer using the USB cable that came with the Device.
+
<br>1. Plug the Device into your Computer using the USB cable that came with the Device.
−
# You should see a window telling you you've plugged in a device (possibly installing drivers)  
+
<br>2. You should see a window telling you you've plugged in a device (possibly installing drivers)  
−
# You should also be able to see the device in Windows Explorer under Computer.
+
<br>3. You should also be able to see the device in Windows Explorer under Computer.
 
<br><span style="color:orange">'''Fourth'''</span>
 
<br><span style="color:orange">'''Fourth'''</span>
−
# High5 Support or Sales will provide you with the installer file.  
+
<br>1. Download the barcode installer at http://high5software.com/downloads/Barcode
−
# Double click on SMEBarcodeInstaller.msi  
+
<br>2.  Double click on SMEBarcodeInstaller.msi  
−
# Follow the on Screen Prompts and select '''Default Directory''' when asked.
+
<br>3. Follow the on Screen Prompts and select '''Default Directory''' when asked.
 
<br><span style="color:orange">'''Fifth'''</span>
 
<br><span style="color:orange">'''Fifth'''</span>
−
# Once the install process is finished on the device (You can squeeze the trigger to display the screen on the device pressing keys activates that key and could interrupt the install process)  
+
<br>1. Once the install process is finished on the device (You can squeeze the trigger to display the screen on the device pressing keys activates that key and could interrupt the install process)  
−
# Squeeze the Trigger and the '2' button together for at least 10 sec. The device screen will flash white then go black and then go white again at this point you can release the button and trigger.  
+
<br>2. Squeeze the Trigger and the '2' button together for at least 10 sec. The device screen will flash white then go black and then go white again at this point you can release the button and trigger.  
−
# This is called a Cold-Boot if the device ever starts to act funny you can perform this and it will return to normal.  
+
<br>3. This is called a Cold-Boot if the device ever starts to act funny you can perform this and it will return to normal.  
−
# Once the device boots you should see SME Barcode as the first item on the list.
+
<br>4. Once the device boots you should see SME Barcode as the first item on the list.
  
 
== Enabling wifi on the device: ==
 
== Enabling wifi on the device: ==
  
−
# On the MT-2090, scroll and select '''Config..'''
+
<br>On the MT-2900 Scroll and Select Config..
−
# Scroll to and select '''Wireless Companion'''
+
<br>Scroll to and Select Wireless Companion
−
# Select '''Find WLAN's''' scroll to the desired one and press '''ENT''' and select '''Connect.'''
+
<br>Select Find WLAN's scroll to the desired one and press ENT and select Connect.  
−
# Follow the wizard entering your information using the '''TAB''' key and Direction buttons. press the yellow button to enable/disable the letters on each number pad. (press the number -rapidly, multiple times to cycle through letters lowercase the upper
+
<br>Follow the wizard entering your information using the TAB key and Direction buttons. press the yellow button to enable/disable the letters on each number pad. (press the number -rapidly, multiple times to cycle through letters lowercase the upper)
−
# You will need to set your wireless mode properly, please check with your admin on how to setup the wifi.  The following are specific settings for the wifi:
+
<br>When you get to the screen that says Profile Entry Encryption Type:  tab to the check box saying "For added security - Mask Characters entered" Enable letters using the yellow button and press 0 This should unselect the check box.
−
## Profile Name:  This can be any descriptive name
+
<br>Disable letters using the yellow key.  
−
## ESSID: This must match your wifi name and will match the same name that you would see on a PC or SmartPhone when you scan for wifi networks.
+
<br>Press the blue key and then ESC until you are back to the Config screen
−
## Operating Mode: Infrastructure is the most common.  Ad-hoc requires a lot more settings.
+
<br>Once again select Wireless companion and Options
−
## Country:  USA most likely.
+
<br>Cycle through the listbox until you get to Regulatory  
−
## Security Modes:  This should match your security setting on the wifi.  Below are some descriptions of options:
+
<br>TAB to Enable 802.11d and deselect this using same process as previously for check boxes.
−
### Legacy(Pre-WPA):  This is used for WEP systems
+
<br>TAB to Save and press ENT
−
## Authentication: None is most common
+
<br>Disable letters using the yellow button
−
## Encryption (The following settings are if you are WEP or Legacy (Pre-WPA) settings:
+
<br>Press the blue button and ESC  
−
### Open: If your wifi has no encryption.
+
<br>You should see signal bars in the top right of the screen
−
### WEP-40
+
<br>Once at the Config screen press 0 to return to the Home screen
−
### WEP-128
+
<br>
−
## Preshared Key: If your security key is 26 numbers, then most likely youare using Hexadecimal Keys rather than Pass-Phrase.  Be sure to set the option for Hexadecimal or Pass-Phrase to match your wifi setting.
 
−
## UNCHECK "For added security- Mask characters entered".  This is VERY important because this device is so hard to enter letters and characters, if you can't see the entered data, you will probably make a mistake.  This does not affect your security except whil you are entering the password. To uncheck this, tab to that field and then select the 0 key.
 
−
### When you get to the screen that says Profile Entry Encryption, type:  tab to the check box saying "For added security - Mask Characters entered" Enable letters using the yellow button and press 0 This should unselect the check box.
 
−
## For Hexadecimal, enter the code in Key 1.
 
−
# Once again select Wireless companion and Options
 
−
# Cycle through the listbox until you get to Regulatory  
 
−
# TAB to Enable 802.11d and deselect this using same process as previously for check boxes.
 
−
# TAB to Save and press ENT
 
−
# Disable letters using the yellow button
 
−
# Press the blue button and ESC  
 
−
# You should see signal bars in the top right of the screen
 
−
# Once at the Config screen press 0 to return to the Home screen
 
  
 +
== WebService: ==
  
−
It's a good idea to test the wifi to make sure it's working properly as it's possible to see the wireless bars, but not really have proper access.
+
<br>Lastly we need to Update your webservice so it provides the Barcode functionality.
−
# From the main screen select Configure>Wireless Companion>Wireless Diagnostics>Ping or Traceroute.
+
<br>
−
# Enter a IP address such as 4.2.2.2 which is accessible from anywhere and accepts pings (and is a little easier to enter). 
+
<br>You can download it here: http://high5software.com/mediawiki/index.php?title=CustomerPortal_and_TechPortal_Install_Guide
−
# Select Enter
+
<br>Follow the directions provided on the website. Once you pull up the webservice on your computer as described in the directions, click on Check DB connection if this functions normal you are good to go.
−
# If your wifi is setup properly, you should see a successful Rx or traceroute.
+
<br>Once you have got this far Email me back and I will enable Barcode for you and provide you with access codes.
−
# If you are not getting a successful receive on the ping or traceroute, then you will need to reconfigure your wifi settings.  You will need to get help from the wifi network admin because there are numerous wifi settings and passwords that High 5 Software would not know.
+
<br>
−
 
+
<br>After this is complete please visit our wiki site on how to use the barcode device.  
−
== WebService ==
+
http://high5software.com/mediawiki/index.php?title=Barcode_for_SME
−
 
 
−
Note: This section is only required if you have not setup webservice for SME yet. The same webservice is used for TechPortal, Android for SME, CustomerPortal, SubcontractorPortal, and incoming Automated email for SME, so if you already have these products, you will not need to re-install the webservice.
 
−
 
 
−
If you do not have WebServices, go to this page for installation instructions:
 
−
[[SME Web Services Installation Guide]] or [[CustomerPortal and TechPortal Install Guide]]
 
−
 
 
−
== Use the Barcode ==
 
−
After this is complete please visit our wiki site on how to use the barcode device.  
 
−
[[Barcode_for_SME]]
 

Please note that all contributions to High5Wiki may be edited, altered, or removed by other contributors. If you do not want your writing to be edited mercilessly, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource (see High5Wiki:Copyrights for details). Do not submit copyrighted work without permission!

Cancel Editing help (opens in new window)
Retrieved from "https://www.high5software.com//mediawiki/index.php?title=Barcode_for_SME_Installation_Instructions"